20-30kgs of waste per hour with water scrubber

Item	Specification
Model	YD-30C (customer made model)
Main Product List	Primary Combustion Chamber(Main body stainless steel)
	Secondary Combustion Chamber(Main body stainless steel)
	Mix-Combustion Chamber
	Wet Scrubber( Washing Tower)(Main body stainless steel)
	Incinerator Control Case
	Chimney:5.0Meters *(upgrade to Stainless Steel, free cost)
	Italy gas burner: 02 units
	Oil Tank (if oil fuel): 100Liters

Model	YD-30C
Feed Capacity	Average 50 kgs per feeding
Burning Rate	Average 30 kgs per hour
Burning Time per Feed	2 hours
Voltage	220V/380V
Power	6 Kw
Fuel	Natural Gas
Burner	Italy Burner
Feed Mode	Manual
Fuel consumption (Oil)	10.2-20.0 Kgs/Hour
Fuel consumption (Gas)	12.2-24.0m3/Hour
External Dimensions	170 x 140 x 190cm (main body)
Internal Dimensions	55 x 55 x 85cm(Primary Chamber)
Waste combustion chamber	250Liters
Post Combustion Chamber	140Liters
Oil Tank Capacity	100 Liters
Door Opening	38 x 48cm
Chimney	5.0M
Gross Weight	3300kgs
Chamber Material	Refractory Concrete
Max. Heat Value	200,000Kcal/Hr.
Operation Technical Specifications
Solid Chamber temperature	8000C -10000C
Gas Chamber temperature	10000C -12000C
Chamber Anti-Rate	13500C
Residency time	2.0 Sec.
Burning efficiency	＞98%
Waste Lower Calorific Power	3000Kcal

Medical Environmental 

---

 

WWW.HICLOVER.COM

Waste Incinerators

Medical Waste Incinerator

Pet Animal Cremation

Solid Waste Incinerator

Tel:  +86-25-8461 0201   

Mobile: +86-13813931455(whatsapp/wechat)
Website: www.hiclover.com  
Email: sales@hiclover.com
Email: hicloversales@gmail.com  

Nanjing Clover Medical Technology Co.,Ltd.

 

2020-02-07

MEDICAL WASTE INCINERATOR (50 �C 60kg/hr)

Medical Waste Incinerator, 50 to 60 Kg/hr
Support Health Sector Support Project
Point of Installation (Hospitals) Moi Voi, Makindu, Maragua, Eldama Ravine and Isiolo District Hospitals
1.    General Description
Supply, delivery, installation and commissioning of a medical waste incinerator suitable for disposal of Medical, General and Pathological waste in a safe and clean environment.  The unit shall consist of two chambers and operate on the principal of controlled air and temperature. The unit shall consist a particulate remover (scrubbers) as stipulated in waste management regulations, 2006 (Legal notice NO. 121 of 29th September, 2006).  The Unit shall be fully automatic and controlled by an automatic electronic controlled system except loading system which shall be manual.  The unit shall be capable of incinerating between 50 to 60 kg of solid medical waste per hour.  It shall be constructed from mild or aluminized steel lined with refractory material.
Main unit
Application For incineration, general and pathological
Capacity   50 �C 60 kg/h burn rate
Type Two  combustion chambers type; primary  and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
Operating time                Minimum 8 hours daily
Operating temperature     From 850 0C to 1200 0C, Automatic controlled
Residual Ash                    5 to 10%
    3.2     Primary Chamber
Construction Constructed from heavy duty mild or aluminized  steel Or
equal and approved equivalent
Insulation material            Refractory material lining similar or equal to calcium 
Silicate and hot face combination of heavy duty brickwork
Internal Construction        Fixed hearth type complete with gratings, concave bottom
and charging door, lined with refractory material
Charging Door                   Suitable for manual loading of wastes and with smooth 
Dear seal equivalent of Ceramic seals with hinges.
Door Lock                          Automatic, Electric type
Ash removal door    Provided, for removing resultant bottom ash leftovers                              from the Primary chamber
Gratings   Provided
Loading Manual loading of waste
Primary Burner                        Fully automatic, with fuel, temperature and speed controls with ignition system, flame detector, Air fan complete with safety features, flame failure,  Diesel fired fuel injector type and Flange mounted                                                                                                    
Blower Provided. For supplying excess combustion air through the distribution system with speed control system
Temperature Minimum exit 850 0C
Observation port To be provided with protective glass type
Construction   Constructed from heavy duty mild or aluminized steel or equal and approved equivalent
Insulation Refractory material lining
Combustion Temperatures        Above 850 0C, controlled electronically
Gas residue or retention Time       > 2 second at minimum 850 0C
Secondary Burner                    Provided, Diesel fired, fully automatic, with fuel, temperature and speed controls, With ignition system,                                                                  Flame detector, Air fan, Complete with safety features, flame failure Diesel fired fuel injector type.                                                                  Flange mounted
Ejector Provided, Venturi type, for cooling the flue gases
Combustion Air Fan Provided for supplying combustion and creating a negative drift and turbulences
Temperature Maximum  1600 0C